6056068三并左出线规格书.xls

Xingke Professional Li-ion Battery Co.,ltd.Date：
Approval
Tel：+86-755-84715111 Fax：+86-755-84715777 Postcode：518129 Xingke Professional Li-ion Battery Co.,ltd.
1 PACK batterys' basic Specifications and standards 4 Protect board component and circuit picture Note: This specification is valid for 6 months from the date of release. Because of the corresponding process changes and other factors that leads to the changes in the specifications, the product specifications should be assistant with new subjects. Xingke Professional Li-ion Battery Co.,ltd.
PACK（XK-605068*3P)battery
1.PACK batterys' basic Specifications and standards
XKTD rule or according ascustomer requirement.
Xingke Professional Li-ion Battery Co.,ltd.
note about the PACK battery ,you can choose the ROHS authentication or no ROHS authentication.
4.Protect board component and circuit picture Xingke Professional Li-ion Battery Co.,ltd.
Appendix 1 Battery XK-605068*3P
This specification is applied to Lithium Ion Battery manufactured by Xingke Professional Li-ion 2 Product and Model Name
2.1 Product：Polymer Lithium Ion Battery 3 Ratings
-10~+40℃ Recommended storage temperature: 25 4 Outline Dimensions and Appearance
See attached drawing for XK-605068*3P(Fig.1).
Thickness：6 MAX. (Measured with weighting 300gf at 25±5℃) Width：50.5 MAX.（Measured with weighting 300gf at 25±5℃） Length：68.5 MAX.（not including tabs） This thickness will be swelling when high temperature storage or operation in high temperature.
There shall be no such defect as scratch, flaw, crack, rust, leakage, which may adversely Xingke Professional Li-ion Battery Co.,ltd.
5 Performance
Test should be conducted with new batteries within one month after shipment from our factory and the cells shall not be cycled more than five times before the test. Unless otherwise defined, test and measureent shall be done under temperature of 25±5℃ and relative humidity of 45~85%.
The test results are not affected evidently by such conditions of temperature 15~30℃ or humidity The dimension measurement shall be implemented by instruments with equal or moreprecision Standard class specified in the national standard or more sensitive class having inner impedance Standard class specified in the national standard or more sensitive class. Total external resistance including ammeter and wire is less than 0.01Ω.
Impedance shall be measured by a sinusoidal alternating current method(1kHz LCR meter).
Test procedure and its criteria are referred as follows: Standard Charging: Constant current charging at 0.5CmA ( 3000mA ） to 4.2V, then constant voltage charging at 4.2V to cut-off current≤0.02CmA(120mA), time≤3.5hours.
Unless otherwise defined, 30min,rest period after charge,30min,rest period after discharge.
(1) Open-Circuit Voltage measured within 24 hours after LCR meter) after standard charge at25±5℃.
The capacity on 1800mAdischargeshall be measured after standard Xingke Professional Li-ion Battery Co.,ltd.
5.6.1 Temperature Dependence of Capacity (Discharge) Cells shall meet the discharge capacity requirements listed in the below table under respective discharge temperatures. The capacities are to be measured with constant discharge current 0.2CmA (2.75V cut-off) after standard charge at 25±5℃.
30min rest period after standard charge, 0.2CmA discharge to a cut-off voltage of 2.75V, 30min rest period, the capacity shall be measured after 300 cycles of standard charge and 0.2CmA discharge to a cut-off voltage of 2.75V at 25±5℃.
The capacity on 0.2CmA dischargeshall be measured after standard charge and then storage at 25±5℃ for 85% CS charge and then storage at 60±2℃ for 75% CS New battery,after about half charge after a period of storage at 25±5℃ no more than 3 months (storage 180 days without load at 25±5℃). The remaining available capacity is ≥80% CS. The capacity is determined with the capacity of the by the most of preceding three cycles.(0.2CmA Xingke Professional Li-ion Battery Co.,ltd.
After standard charge, the battery is to be tested as Vibration testFrequency:10~55Hz(sweep:1Hz/min) Direction: X/Y/Z axis for 90~100min. The batteryis to be tested in three mutually perpendicular toeach axis.
Drop the battery in the shipment condition(full-charge)from 1m height onto 5cm or thicker concrete No fire, no explosion, no Drop Test with p-tile on it 3 times each of X, Y, and Z 6 Dimensional Drawing of XK-605068*3P
Xingke Professional Li-ion Battery Co.,ltd.
Specifications
T（MAX）
W（MAX）
L（MAX）
1.25±1.0mm
42±1.5mm
Appendix 2
1 Handling Instructions
Read and observe the following warnings and precautions to ensure correct and safe use of Li-ion Failure to observe the following precautions may result in battery leakage, overheating, explosion and — Do not immerse the battery in water or allow it to get wet.
— Do not use or store the battery near sources of heat such as a fire or heater.
— Do not use any chargers other than those recommended.
— Do not reverse the positive(+) and negative(-) terminals.
— Do not connect the battery directly to wall outlets or car cigarette-lighter sockets.
— Do not put the battery into a fire or apply direct heat to it.
— Do not short-circuit the battery by connecting wires or other metal objects to the positive(+) and — Do not carry or put the battery together with necklaces, hairpins or other metal objects.
— Do not strike, throw or subject the battery to sever physical shock.
— Do not pierce the battery casing with a nail or other sharp object, break it open with a hammer, or step — Do not directly solder the battery terminals.
— Do not attempt to disassemble or modify the battery in any way.
— Do not recharge the battery near a fire or in extremely hot conditions.
Warning!
Failure to observe the following precautions may result in battery leakage, overheating, explosion and/ Xingke Professional Li-ion Battery Co.,ltd.
— Do not place the battery in a microwave oven or pressurized container.
— Do not use the battery in combination with primary batteries(such as dry-cell batteries) or batteries of — Do not use the battery if it gives off an odor, generates heat, becomes discolored or deformed, or appears abnormal in any way. If the battery is in use or being recharged, remove it from the device or charger immediately and discontinue use.
— Keep the batteries out of the reach of children. If a child somehow swallows a battery , seek medical — If the battery leaks or emits an odor, immediately remove it from the proximity of any exposed flame. The leaking electrolyte can ignite and cause a fire or explosion.
— If the battery leaks and electrolyte gets in your eyes, do not rub them. Instead, rinse them with clean running water and immediately seek medical attention. If left as is, electrolyte can cause eye injury.
Caution!
Do not use or store the battery where is exposed to extremely hot, such as under window of a car in direct sunlight in a hot day. Otherwise, the battery may be overheated. This can also reduce battery performance and/or shorten service life. Use the battery only under the following environmental conditions. Failure to do so can result in reduced performance or a shorten service life. Recharging the battery outside of these temperatures can cause the battery to overheat, explode or catch fire.
When discharging the battery: -20℃～60℃ When stored up to 30 days: -20℃～45℃ When stored up to 90 days: -20℃～35℃ In cases where children use the battery, instruct them on the contents of the user’s guide and keep an eye on them to ensure that the battery is being used correctly. If the battery leaks and electrolyte gets your skin or clothing, immediately rinse the affected area with clean running water. If left as is, skin inflammation can occur. For directions on battery installation and removal, read the instruction manual that accompanies the equipment in which the battery will be used.
If a device is not used for an extended period, the battery should be removed and stored in a cool, dry place. Otherwise, resting or reduced performance may occur.
If the terminals of the battery are dirty, wipe them clean with dry cloth before use. Otherwise, solid electrical contact may not be charged with the equipment, and this can cause power outages or charging Xingke Professional Li-ion Battery Co.,ltd.
2 Period of Warranty
The period of warranty is one year from the date of shipment. Guarantees to give a replacement in case of cells with defects proven due to manufacturing process instead of the customers abuse and misuse.
3 Shipment
4 Amendment of this Specification
This specification is subject to change with prior notice.

Source: http://www.gotronic.fr/pj-791.pdf