Otkon.com.tr

STEPPING
MO
T
O

RS
5 Phase with A
5-Phase with DC Driver
Stepping
Controller
2 Phase with DC Driver
SG8030JY ························································B-244
Stepping
Accessories
ORIENTAL MOTOR GENERAL CATALOGUE
STEPPING
Compact and Simple Controllers
MO
SG8030JY
T
O
RS

The SG8030JY is a compact controller that
switches between two control methods
according to the application: sequential
positioning and data selection positioning.

With sequential positioning mode, you execute
up to four positioning control operations in the
pre-determined sequence by just inputting the

5-Phase with A
start command from the programmable
controller. In data selection positioning mode,

positioning is controlled by selecting one of four
sets of pre-registered positioning data and
Now the Panel-Mount Model isavailable.Allow conventional delay for inputting the start command from the
shipping. See your agency for detail.
programmable controller.
SG8030JY-D
SG8030JY-U
5-Phase with DC Driver
Main Specifications
High-Performance Packed in
Set data with touch keys on front panel (record in 48mmϫ48mm Compact Units
Ⅲ With dimensions of 48mmϫ48mmϫ83.8mm, these units are the smallest of Oriental Motors controllers.
They come in Flush Mounting and Recessed Mounting Starting pulse speed 100-10000 HzAcceleration rate 1-100 ms/kHz For the acceleration/deceleration
pattern, you may select the linear or
Stepping
S-shaped pattern.
Ⅲ In addition to the linear acceleration/deceleration acceleration/deceleration along an S-shaped pattern.
Sensor detection of home throgh designation of 2-Phase with DC Driver
When you select this S-shaped pattern, the motor can mechanical home detection direction of rotation.
DC 24 V photocoupler input, input resistance 4.7 k Ω current sinking inputPNP transistor output linked to photocoupler, 24V The control methods can be switched.
DC, 25mA or less, current sourcing output Ⅲ You can also switch the control between sequential positioning and data selection positioning.
Stepping
Functions
Ⅲ These stepping motor controllers, they have all the most commonly used functions.
ⅷControl modes: External, Program, Test ⅷOperating modes: Positioning, Return to mechanical Example of Basic System Configuration
Accessories
SG8030JY
ORIENTAL MOTOR GENERAL CATALOGUE
STEPPING
Operating methods
MO
Sequential Positioning Type
Data Selection Positioning Type
T
O
RS
ositioning
P

Sequential positioning type performs positioning in order from the Data selection positioning type performs positioning in order after first data every time a START signal is input.
positioning data 1-4 are selected and a START signal is input.
5 Phase with A
External input mode
When a START signal is input, it moves towards the preset sensor at the operating pulse speed (VR), to return to the origin.
Return to mec
5-Phase with DC Driver
It continuously operates as long as a CW or CCW scan signal is When operating at the continuous operation mode, it keeps the input, no matter what operating mode is set (It reduces the speed operation as long as a CW or CCW scan signal is input (It reduces and stops when a OFF signal is input).
the speed and stops when a OFF signal is input).
operation
The next four operation can be confirmed manually by using the Data selection positioning operationContinuous operation Confirmation of
Stepping
operation man
Wiring diagram
Signal table
2 Phase with DC Driver
Signal names and functions of Sequential positioning type andData selection positioning type differ in Pin No. 1, 10, 11 only.
q When in the Sequential positioning type w When in the Data selection positioning type Stepping
SG8030JY
q : Switching positioning and home detection w : Switching positioning and home detection Input Start signal for Positioning and Home detection operation Accessories
7 Pulse <CW pulse> Output Pulse <CW-pulse output terminal> Output Direction <CCW-pulse output terminal> ✽1 The pulse output section uses a constant-current circuit, so no external Input Stop all operation Stop busy output If another power supply is used for the pulse output section, for example +5V power, connect the 24V DC and another power supply GND terminals each other.
✽3 This should be conductive (B contact) during normal operation.
When not using the emergency stop input signal, always connect to the The "E.StoP" message is displayed when the power supply goes off.
✽4 The names in angle brackets < > signals are for data selection The operating modes given in square brackets [ ] are activated when operationmode select input is on. The names in angle brackets < > signals are for 2-pulse output.
ORIENTAL MOTOR GENERAL CATALOGUE
STEPPING
MO
T
O
RS

Dimensions Scale 1/4, Unit=mm
Mass: 0.1kg (Without accessories)
5-Phase with A
SG8030JY-D
SG8030JY-U
5-Phase with DC Driver
Stepping
2-Phase with DC Driver
Stepping
Accessories
ORIENTAL MOTOR GENERAL CATALOGUE

Source: http://www.otkon.com.tr/dosya/SG8030%20Serisi%20Katalog%20(0,2%20Mb).pdf

Microsoft word - clinical studies of alkaline water

CLINICAL STUDIES OF ALKALINE Reduced water Electrolyzed water Alkaline /Acid water Microwater There have been many studies by Doctors inJapanese Hospitals on the Benefits of using AlkalineWater. Below are a few now translated into English Fluid replacement promotes optimal physical performance.  Electrolyzed-reduced water scavenges active oxygen & protects The mecha

Enero 2008

Comunicado de Prensa Descubre cómo lucir una cabellera saludable y estilizada con Smooth ‘N Shine • La marca Smooth ’N Shine presenta su nuevo mousse Diamond Luster Anti-Frizz , así como la nueva imagen de su línea actual de mousses. • Su innovadora acción termo-protectora ayuda a sellar la estructura capilar, protegiendo el cabello contra el calor.

Copyright © 2010-2014 Medical Pdf Finder